Palo alto layer 3 deployment

Now we will discuss the third one — Layer3 or L3 mode. Here is our topology:. If we were not using virtualization, we could just plug our physical PCs into this switch. This aggregation switch is connected to the rest of our network or the Internet. The most important setting here is the interface type. It is Layer3. We will use the default routing instance or virtual router and will assign the security zone later, once we create it.

Here we can see that we set up the IP address to be This is what our protected PCs or VMs will use as a default gateway. This gateway can be a Layer 3 switch, a router or another firewall. We give this route a name and specify the destination. This can be single network or a host, or can be a default route which is given in form 0. We give an interface through which these networks will be reachable and specify a next hop router IP address.

Please note that we did not specify any routes towards our protected hosts because they are directly connected. If we had another L3 device in between, we would need to statically or dynamically route to our protected destination. They have to be of type Layer3.

Layer 3 Deployments

Finally, in order to pass traffic between our zones, we must have a security policy in place. We will make a policy that permits all traffic between zones. We can, should and will make this policy more restrictive at a later point. The resulting policy looks like this:. We can now tweak our security policy to allow or disallow certain types of traffic, but that is another story. You are commenting using your WordPress. You are commenting using your Google account. You are commenting using your Twitter account.

You are commenting using your Facebook account. Notify me of new comments via email. Notify me of new posts via email. Skip to content. Home About. Thanks for reading! Share this: Twitter Facebook LinkedIn. Like this: Like Loading This entry was posted in FirewallPaloaltoSecurity and tagged firewallpalo alto. Bookmark the permalink. December 8, at Leave a Reply Cancel reply Enter your comment here Fill in your details below or click an icon to log in:.Need support for your remote team?

Check out our new promo!

palo alto layer 3 deployment

IT issues often require a personalized solution. Why EE? Get Access. Log In. Web Dev. NET App Servers. We help IT Professionals succeed at work.

How to configure multiple vlans to go through a layer 3 firewall interface. Graycon asked. Medium Priority. Last Modified: Hi there, I am currently in the process of breaking one big corporate vlan into 3 smaller ones and am having issues with internet connectivity in my lab. I am using an HP Layer 3 core that will support the 3 corporate vlans as follows: vlan Building 1 - vlan-interface10 It's address is The DHCP server is also on vlan 10 and has scopes for all 3 vlans which are working.

All the LAN routing on the core is simple direct attach routes as everything comes back to the core's vlan-interfaces. I can't seem to get vlan 20 or 30 to connect to the internet after adding a static 0.

How to configure multiple vlans to go through a layer 3 firewall interface

VLAN 10 works fine. If i am routing all internet traffic through Another thing is that i can ping the firewall LAN interface from vlan 10 but not the other vlans but i'm not sure if that is just a security rule.

I've read on using sub-interfaces or using a physical interface on the Palo alto for each vlan and put them all in the same security zone.

Any ideas of how i should do this? Start Free Trial.This subredditt is for those that administer, support, or want to learn more about Palo Alto Networks firewalls. We are not officially supported by Palo Alto networks, or any of it's employeeshowever all are welcome to join and help each other on a journey to a more secure tomorrow. Do you have support related questions? Check the Support Site.

I am new to the Palo Alto scene. I have a PA coming on Tuesday. What's the best way to set it up? Since I am working from home for the next few weeks, my use case is an at-home deployment. I have read the beginning of the Admin Guide, and see that it refers to a Day 1 configuration.

It's not clear to me what that is and what it does, in detail. Is that described anywhere? Seems like that's a logical first step easy to insert, easy to remove if issues.

The Day One config from Iron Skillet are great.

Getting Started: Layer 3, NAT, and DHCP

They have also have nice explanations in the documentation. Does the Day One config set it up as virtual wire or layer 3? I keep looking for a picture that summarizes the setup but not finding one.

This makes a difference. This is how I have it setup at my house: Configure all the Device setup information, General settings, Management port etc. Get your dynamic updates able to communicate with the Palo server and start updating the content updates and do a software upgrade if you need to.

This is a high level overview but I would maybe look for examples of small office configs. I treat my home like one of our remote offices Mine is setup just like that in a sense. There are plenty of examples out there. Ultimately however you set it up you will have fun. Maybe you go the vwire route like it has been suggested then you decide you want to go the L3 route. Remember vwire is making the firewall a bump on the wire. If you have the lab I would make it a L3 device and learn as much as you want!

But good luck and have at it! I have Verizon Fios. That's good to know about GlobalProtect because that's one of the key features that I want to use. I don't have experience connecting a PA to Verizon Fios. If GP is what you want to use then vwire is not the route. There is a lot of good information out there on config examples.

I have been working on PA for the past 2 years and firewalls for the last 6. I love the Palos. Good luck. Have fun!! Never thought of using a firewall for layer I only use them on my personal lab unit for 2 reasons.This post will provide a foundation for later ones that take a deeper dive into the features of the device. Sound simple? One of the great strengths of the Palo Alto device is the ability to choose from a fairly comprehensive selection of deployments.

In addition to the three methods above there is a fourth deployment option for called Tap mode. Keep in mind that picking one deployment method is not to the exclusion of the others. In fact you can deploy any number and combination of deployments with your only limitation being the number of interfaces and required designed.

Through the use of network segments and with a choice of the type of inspection, an administrator will quickly find uses for the Palo Alto firewall outside the standard perimeter security device. Virtual wire deployments is the simplest of the three. The virtual wire contains no switching and routing information and so by default packets are sent across the wire with no modification. One of the great advantages of this method is that it requires no modification of your existing infrastructure.

Virtual wire implementations can be put on line and taken off as fast as it takes you to swap cables. Once again the device can shape traffic as required using this method.

For the Layer 3 deployment, as expected, traffic is routed between interfaces. This is the most common firewall deployment and probably familiar to most.

palo alto layer 3 deployment

This is the most powerful of the three as it allows you to take full advantage of the Palo Alto features. Virtual Routers are much like they sound; they allow you to group interfaces on which routing statements and protocols can be assigned. The advantage here is that there is not just a singular routing table and protocols for the entire device, but a unique set of routing tables and protocols for each virtual router which can be assigned to any number of interfaces. At the bottom of the Virtual Routers window, click on Add.

These will act as the interfaces cabled into our external and internal networks, respectively. If we were using multiple interfaces we could assign the various administrative distances and balance traffic accordingly. Below the General section click on the Static Routes. At the bottom of the IPv4 tab click Add. Click OK. We also need to map a default route for the external interface. Set the Destination to 0. Once again use IP Address and this time we set the gateway as Zones combine one or more interfaces to be used for traffic to ingress or egress the device.In the previous installments of Getting Started, we covered how to set up the firewall from scratch.

In this next series, we'll be covering more advanced configuration features that will help you fine tune your firewall to better suit your environment. This week, we'll take a look at Layer 2 interfaces and how the firewall can be set up to provide bridging between VLANs while enforcing security policies and providing threat prevention to keep your network secure.

We'll start with a simple example where we have two Layer 2 interfaces in the same zone and the same VLAN. This configuration will ensure your hosts all remain on the same IP subnet, but can be segregated depending on their role.

More interfaces can be added to provide even more segments or tagged subinterfaces can be added in a similar fashion as described in Getting Started: Layer 3 — Subinterfaces. You may have noticed some Layer 3-looking configuration in the VLAN configuration earlier, and this is where we will need to enable the functionality.

Any sessions originating from your internal hosts to the outside world will be handled by the firewall as coming from the Layer 3 Trust zone going to the Layer 3 Untrust zone. Please be aware you may need some additional configuration to allow for outbound connections, including the default route in your virtual router, NAT configuration so the internal IP subnet is translated to the public IP address of the firewall and maybe a DHCP server to automatically assign IP addresses to workstations joining your network.

I hope you enjoyed this article and found it useful. Feel free to post any remarks or questions in the comment section below. For more details on Layer 2 interfaces, please take a look at the Tech note on Layer 2 Networking.

palo alto layer 3 deployment

What more can my firewall do? There will already be one default VLAN interface present, which you can reuse if you like, but we'll create a new one by clicking the Add button. You'll assign the interface an ID, add any relevant comment and assign the interface to the default Virtual Router and add it to the Trust zone. Note that the ID is simply an identification number for the interface and does not influence any Simply give it a name and click OK for now. The VLAN interface should look somewhat like this.

Go ahead and click OK. This is because we have not yet created any Layer 2 Security Zones. Any Security Zone configured on the firewall is also attached to a specific network type, like Layer 3, VWire, or Layer 2. This is to allow traffic to pass from Layer 2 to Layer 3. We'll take a look at that after we've completed this phase of the Layer 2 introduction. The last stage is to create an intrazone security policy to allow more granular control over applications connecting both segments and applying security profiles to these sessions.

Open the Policies tab and navigate to Security on the left pane. Click Add to create a new security policy. From the Rule Type dropdown, select 'intrazone' as the Type. Next, navigate to the Source tab, click Add, and set the source zone to L2-Trust.

Because this is an intrazone Security Policy, the destination zone selection has been made inaccessible and is dependent on the source configuration. Set the applications to what is appropriate between the segments. These are solely the applications you want to allow between the internal hosts. This does not apply to any connections going to or coming from other networks.

palo alto layer 3 deployment

Lastly, set security profiles so any sessions between your internal hosts are also inspected for vulnerabilities, exploits, viruses, and so on. Your security policy should now look similar to this: Rule1, as seen above, will be used in the next segment, Layer2 Routing.Palo Alto Networks Community Supported. New in this version is the ability to protect existing workloads as well as net new.

The process uses naming conventions and instance tagging for configuration. Partner Community Supported. The VM-Series is then configured using Ansible scripts. Once completed, the user will have built a Hub, and 3 subscribing VPC spokes.

In AWS environment we have containers that do the job and then terminate. How is is possible to do a security policy on containers? DAG is not detecti Basically we need to have outbound to inbound NAT rule with a ela The status of both devices on Pan I can do EC2 instances easy enough but struggling to find a way to dyna Note: In order to view ALL of the articles in this section and to engage in discussions on this platform, you must register for an account on Live Community.

Some articles may not be viewable to unregistered users. Register for a Live Community account. Note : In order to create a case, please create or active an account and register your device, which can be done in the Customer Support Portal.

This area provides product support for all Palo Alto Networks Customers. Login to the Customer Support Portal. Turn on suggestions. Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type. Showing results for. Search instead for.There may be several network segments in your organization to segregate user workstations from public web servers.

The first configuration we'll look at builds on where we left off in the previous getting started guide. The firewall has Layer 3 interfaces and we're now going to change the trust interface so it can communicate with a trunked switch interface. We'll be switching our configuration from a regular interface to tagged subinterfaces.

In the subinterface configuration, we need to assign an interface number and a tag. The tag needs to match the VLAN exactly, but the interface number may be different. Add the interface to the 'default' Virtual Router and assign it to the 'trust' Security Zone.

So we'll need to add a second subinterface and set it to VLAN tag We'll also create a new Security Zone so we can apply different security policy to it. The next step is to create a NAT policy to allow hosts on the internet to reach the webserver via the external IP address of the firewall. The destination zone is untrust because the firewall will try to determine the destination zone of a received packet based on its routing table.

In this case, the original destination IP address, before NAT is applied, belongs to the untrust zone. The last step is to create security policies to allow the trust and untrust zone to access the web server. We'll set the destination to 'dmz' and the destination address to the external IP of the firewall. Repeat this step for a security policy from the trust zone, so additional applications can be added.

In the destination, we'll set Security Zone 'dmz' and the internal IP address of the webserver.


comments

Leave a Reply

Your email address will not be published. Required fields are marked *

1 2